Winnipeg Free Press - PRINT EDITION

How to re-point your chimney

  • Print

There are a few key things homeowners need to think about when preparing to repair their brick or cinder-block chimneys.

Chimneys are being converted to the metal-insulated type of chimneys, rather than the old flue-liner type with solid brick/block chimney chases. The reason is the devices used in chimneys are also changing. I am seeing fewer traditional wood-burning fireplaces and more controlled-burning appliances in fireplaces, such as heatilators, wood-pellet fireplaces or natural gas or propane fireplaces, which require a different type of insert to properly exhaust gases created when fuel is burned.

The change in how we use fireplaces is also affecting how they age.

Let's deal with a home that has a brick or cinder-block chimney. You will notice a line between the bricks or cinder-blocks; this is the mortar line. Brick mortar lines can deteriorate over time as they are exposed to the elements. If the mortar lines deteriorate, they will allow in moisture. This can freeze during winter and cause further damage to the chimney.

The repair for this is called repointing. Before repointing the exterior of your chimney, you must first make an effort to remove as much of the loose mortar as possible using a small pointed trowel. Once you have removed the loose mortar, wash the mortar lines with an all-purpose cleaner. This will give you a clean surface to work with. Any dirt, algae or other residue can interfere with the bonding process.

Purchase a multi-purpose adhesive such as Weldbond or a pre-mixed concrete adhesive. Brush the adhesive into the mortar lines you are going to repoint, meaning where you are going to put new mortar to replace the old mortar you have scraped out. The adhesive will act as a bonding agent for the new mortar to adhere to.

Once you've properly prepared the surface, get a bag of mortar mix or mortar pre-mixed cement. You have already added the adhesive where the loose material was scraped away. There is no need to add any more adhesive to the mortar mix, but, if you wish, you can add a 1/2 cup (125 mL) of adhesive to two shovels of mortar mix. The consistency should be such that when you grab a handful of this mix, you are able to squeeze it and it will come out between your fingers.

Now you're ready to place the mortar. Do not do this in the direct sunlight or heat. You will place the mortar using a pointing tool. This tool looks like a Z and has two sides to it: one side is 3/8 inch (9.5 mm) and the other side is 1/2 inch (1.2 mm). Using a piece of plywood, put a small quantity of mortar on the plywood and push the mortar off of the plywood using the pointing tool into the grove where the mortar is to go.

Once you've done the repairs, wait a month to seal the surface. Seal using a spray bottle filled with an acrylic concrete sealer. Start sealing the brick/cinder block and mortar surfaces at the bottom, working your way to the top of the chimney.

For more home-improvement information, go to

-- Postmedia News


Republished from the Winnipeg Free Press print edition August 24, 2013 F12

Fact Check

Fact Check

Have you found an error, or know of something we’ve missed in one of our stories?
Please use the form below and let us know.

* Required
  • Please post the headline of the story or the title of the video with the error.

  • Please post exactly what was wrong with the story.

  • Please indicate your source for the correct information.

  • Yes


  • This will only be used to contact you if we have a question about your submission, it will not be used to identify you or be published.

  • Cancel

Having problems with the form?

Contact Us Directly
  • Print

You can comment on most stories on You can also agree or disagree with other comments. All you need to do is be a Winnipeg Free Press print or e-edition subscriber to join the conversation and give your feedback.

You can comment on most stories on You can also agree or disagree with other comments. All you need to do is be a Winnipeg Free Press print or e-edition subscriber to join the conversation and give your feedback.

Have Your Say

New to commenting? Check out our Frequently Asked Questions.

Have Your Say

Comments are open to Winnipeg Free Press print or e-edition subscribers only. why?

Have Your Say

Comments are open to Winnipeg Free Press Subscribers only. why?

The Winnipeg Free Press does not necessarily endorse any of the views posted. By submitting your comment, you agree to our Terms and Conditions. These terms were revised effective April 16, 2010.


Make text: Larger | Smaller


Winnipeg leaders speak out on racism

View more like this

Photo Store Gallery

  • A goose flys defensively to protect their young Wednesday near Kenaston Blvd and Waverley -See Bryksa 30 Day goose challenge- Day 16 - May 23, 2012   (JOE BRYKSA / WINNIPEG FREE PRESS)
  • Marc Gallant/Winnipeg Free Press. Local- Peregrine Falcon Recovery Project. Baby peregrine falcons. 21 days old. Three baby falcons. Born on ledge on roof of Radisson hotel on Portage Avenue. Project Coordinator Tracy Maconachie said that these are third generation falcons to call the hotel home. Maconachie banded the legs of the birds for future identification as seen on this adult bird swooping just metres above. June 16, 2004.

View More Gallery Photos


Should tobogganing be banned on city land?

View Results

Ads by Google