Winnipeg Free Press - PRINT EDITION
MIKE HOLMES: Squeaky floors an expanding nuisance
SOME homes are impossible to sneak in and out of, and not because of the latest in high-tech security or an iron-clad exterior.
These homes have squeaky subfloors and noisy stairs loud enough to wake the dead. And it's a growing nuisance in more and more homes.
Some new-home owners think squeaky floors or stairs are older-home issues. Not the case. In fact, if your home is built to minimum code, it might not squeak yet -- but it will, in time. Go and stand in the middle of a room and start jumping -- the floors are going to bounce.
It's classic minimum code. When homes are built to minimum safety requirements -- because that's what minimum code is -- that's all you're getting. It will be safe but it might not be built to last more than 10 years.
Squeaky floors are usually a subfloor issue. Minimum code says subfloors need to be built using 2x8s, 16 inches on centre, with a minimum of 5/8 inches of OSB (oriented strand board) sheathing on top. Not to mention that most builders use a nail gun to install subfloors. Together, it's the perfect recipe for squeaky floors.
If you don't want your floors and stairs to squeak, use plywood -- the real kind -- for the subfloor. There's a lot of debate around plywood, OSB and other types of sheathing for subfloors. Are they comparable? Which one is better? Which one is no good? OSB is even called the "modern version" of plywood. Some kinds are more expensive than plywood.
But bottom line: When I pull up flooring and I see something like particleboard, low-grade OSB or aspenite, I'm not happy. Sixty years ago, subfloors weren't built of plywood, they were built with heavy planks. Plywood might be above code, but if you want to solve squeaky floors for good, it's just one part of the package.
Second, you want to make sure the subfloor is properly glued and screwed to the floor joists; if it's not, there will be squeaking and creaking.
When you use a nail gun to attach subfloor sheathing to the floor joists, the nail sometimes misses the joist. If your basement isn't finished, take a look at the ceiling. You can see how many nails from the floor above missed the joists (a worker would feel the difference when manually nailing them). That means there are fewer nails holding down the subfloor.
When people walk on a floor where the subfloor hasn't been properly secured, the sheathing moves up and down. This motion will eventually cause the nails that did hit the floor joist to pull away. The squeaking will only get worse.
That's why I always glue and screw my subfloors. The glue secures that connection and the screws lock it in place. Remember, nails can pull up; screws don't. This gives us stronger floors that will not move or squeak.
Hardwood flooring also might squeak over time -- it expands and contracts depending on the humidity in the home. Wood treads and risers in stairs also shrink with age. Hardwood usually shrinks in the winter because home-heating kills most of the moisture in the air. That can cause gaps between the hardwood boards, which can lead to creaking. Plus, as hardwood is nailed to the subfloor, shrinking can pull the nails out, and thus the squeaking begins.
If the problem has to do with the subfloor -- either it's not plywood or not properly secured to the floor joists with glue and screws -- the best option is ripping up the finished floor and making the appropriate repairs. That could mean pulling up the subfloor as well and replacing it with better materials and using better products to secure it. It's not a quick fix, or the cheapest. But it solves the problem. That's why a renovation is a great time to get rid of squeaky floors for good.
Another option is blocking, also known as strapping or bridging. It's a good option if the creaking is caused because the floor joists are too far apart. There are different ways of blocking -- it depends on materials and installation. It also depends if there's wiring or duct runs in the way. The way I like to do it, and the way I tell my guys to do it, whenever possible, is to screw a piece of wood in between and perpendicular to the two joists. Usually we're dealing with 2ó8 floor joists so we do eight-inch blocking. But if the floor joists are 2x10s, we use 10-inch blocking.
Blocking adds rigidity and stiffness between floor joists, so they won't move or shift. If you have access to the floor from underneath -- i.e. from an unfinished basement without any drywall on the ceiling -- you can solve the problem upstairs without having to rip up your finished floors. But if the problem is in the subfloor, you're out of luck. Those floors have to come up or you'll have to live with the squeaks.
Catch Mike Holmes in his new series, Holmes Makes It Right, Tuesdays at 9 p.m. on HGTV. For more information, visit hgtv.ca. For more information on home renovations, visit makeitright.ca.
Republished from the Winnipeg Free Press print edition March 16, 2013 F2
Have you found an error, or know of something we’ve missed in one of our stories?
Please use the form below and let us know.
Having problems with the form?Contact Us Directly
More Renovation & Design
More Renovation & Design
(1 of 6 articles for this week)02/21/2015 3:00 AM 0
Fifteen years ago, it was frowned upon to apply for a permit to build an addition called a granny suite. ...
Photo Store Gallery
- Wainscoting turns a dull room into a sumptuous space
- Dividing-wall debacle
- The ultimate space saver
- What to do when leather furniture fades
- Watch out for extra moisture in sun tunnels
- DIYer's dilemma
- Diligence key to keeping furnace vents clear
- Must I heat the cottage over the winter?
- Man making amends sets giving in motion
- Batt insulation can lead to mould grief
- Beating the winter blues
- Comforting new insulation for basements
- DIYer's dilemma
Ads by Google